sidebar
"Foundations of Black Hole Accretion Disk Theory"
Marek A. Abramowicz and P. Chris Fragile 
Abstract
1 Introduction
2 Three Destinations in Kerr’s Strong Gravity
2.1 The event horizon
2.2 The ergosphere
2.3 ISCO: the orbit of marginal stability
2.4 The Paczyński–Wiita potential
2.5 Summary: characteristic radii and frequencies
3 Matter Description: General Principles
3.1 The fluid part
3.2 The stress part
3.3 The Maxwell part
3.4 The radiation part
4 Thick Disks, Polish Doughnuts, & Magnetized Tori
4.1 Polish doughnuts
4.2 Magnetized Tori
5 Thin Disks
5.1 Equations in the Kerr geometry
5.2 The eigenvalue problem
5.3 Solutions: Shakura–Sunyaev & Novikov–Thorne
6 Slim Disks
7 Advection-Dominated Accretion Flows (ADAFs)
8 Stability
8.1 Hydrodynamic stability
8.2 Magneto-rotational instability (MRI)
8.3 Thermal and viscous instability
9 Oscillations
9.1 Dynamical oscillations of thick disks
9.2 Diskoseismology: oscillations of thin disks
10 Relativistic Jets
11 Numerical Simulations
11.1 Numerical techniques
11.2 Matter description in simulations
11.3 Polish doughnuts (thick) disks in simulations
11.4 Novikov–Thorne (thin) disks in simulations
11.5 ADAFs in simulations
11.6 Oscillations in simulations
11.7 Jets in simulations
11.8 Highly magnetized accretion in simulations
12 Selected Astrophysical Applications
12.1 Measurements of black-hole mass and spin
12.2 Black hole vs. neutron star accretion disks
12.3 Black-hole accretion disk spectral states
12.4 Quasi-Periodic Oscillations (QPOs)
12.5 The case of Sgr A*
13 Concluding Remarks
Acknowledgements
References
Footnotes
Figures
Tables

6 Slim Disks

The Shakura–Sunyaev and Novikov–Thorne models of thin disks assume that accretion is radiatively efficient. This assumption means that all the heat generated by viscosity at a given radius is immediately radiated away. In other words, the viscous heating is balanced by the radiative cooling locally and no other cooling mechanism is needed. This assumption can be satisfied as long as the accretion rate is small. At some luminosity (L ≈ 0.3LEdd), however, the radial velocity is large, and the disk is thick enough, to trigger another mechanism of cooling: advection. It results from the fact that the viscosity-generated heat does not have sufficient time to transform into photons and leave the disk before being carried inwards by the motion of the gas. The higher the luminosity, the more significant advective cooling is. At the highest luminosities, it becomes comparable to the radiative cooling (see Figure 8View Image), and the standard, thin disk approach can no longer be applied.
View Image

Figure 8: The advection factor (ratio of advective to radiative cooling) profiles for m˙ = 0.01, 1.0 and 10.0 (here, m˙ = M˙ c2∕16L Edd). Profiles for α = 0.01 and 0.1 are presented with solid black and dashed red lines, respectively. The fraction fadv∕(1 + fadv) of heat generated by viscosity is carried along with the flow. In regions with fadv < 0 the advected heat is released. Image reproduced by permission from [269Jump To The Next Citation Point].

The problem of accretion with an additional cooling mechanism has to be treated in a different way than radiatively efficient flows. Without the assumptions of radiative efficiency and Keplerian angular momentum, it is no longer possible to find an analytic solution to the system of equations presented in Section 5.1. Instead, one has to solve a two-dimensional system of ordinary differential equations (95View Equation) with a critical point – the radius at which the gas velocity exceeds the local speed of sound (the sonic radius). This was first done in the pseudo-Newtonian limit by Abramowicz [8], who forged the term “slim disks”. It has since been done using a fully relativistic treatment by Beloborodov [40]. Recently, Sadowski [268] constructed slim disk solutions for a wide range of parameters applicable to X-ray binaries.

These slim disks are in some sense more physical than thin disks and offer a more general set of solutions, while in the limit of low accretion rates they converge to the standard thin disk solutions. Slim disks are more physical in that they extend down to the black hole horizon, as opposed to thin disks that formally terminate at the ISCO. Slim disks are more general in that they may rotate with an angular momentum profile significantly different than the Keplerian one – the higher the accretion rate, the more significant the departure (see Figure 9View Image). The disk thickness also increases with the accretion rate. For rates close the Eddington limit, the maximal H ∕R ratio reaches 0.3. Finally, the flux emerging from the slim disk surface is modified by the advection. At high luminosities, a large fraction of the viscosity-generated heat is advected inward and released closer to the black hole or not released at all. As a result, the slope of the radial flux profile changes, and radiation is even emitted from within the ISCO (see Figure 10View Image). Due to the increasing rate of advection, the efficiency of transforming gravitational energy into radiative flux decreases with increasing accretion rate. Despite highly super-Eddington accretion rates, the disk luminosity remains only moderately super-Eddington (see Figure 11View Image). The Eddington luminosity may be exceeded because the geometry of the flow is not spherical and the classical definition of this quantity does not apply – most of the accretion takes place in the equatorial plane while the radiation escapes vertically. Thus, the radiation is not capable of stopping the inflow, though it may cause outflows from the surface.

View Image

Figure 9: Profiles of the disk angular momentum (uϕ) for α = 0.01 (left) and α = 0.1 (right panel) for different accretion rates (as a reminder, ˙m = M˙c2∕16LEdd), showing the departures from the Keplerian profile. These plots are for a non-rotating black hole. Image reproduced by permission from [270Jump To The Next Citation Point], copyright by ESO.
View Image

Figure 10: Flux profiles for different mass accretion rates in the case of a non-rotating black hole and two values of α: 0.01 (black solid), 0.1 (red dashed lines). For each value of α there are five lines corresponding to the following mass accretion rates: ˙m = 0.01, 0.1, 1.0, 2.0 and 10.0 (as a reminder, 2 m˙ = M ˙c ∕16LEdd). The black hole mass is 10M ⊙. Image reproduced by permission from [270], copyright by ESO.
View Image

Figure 11: Top panel: Luminosity vs accretion rate for three values of black hole spin (a∗ = a∕M = 0.0, 0.9, 0.999) and two values of α = 0.01 (black) and 0.1 (red line). Bottom panel: efficiency of accretion η = (L ∕LEdd )∕ (M ˙ ∕M˙Edd ) (here M˙Edd = 16LEdd∕c2). Image reproduced by permission from [269].

  Go to previous page Scroll to top Go to next page